09.13.2017 Erosion Effects on "Vera Rubin Ridge," Mars
08.09.2017 Clouds Sailing Overhead on Mars, Enhanced
08.09.2017 Clouds Sailing Overhead on Mars, Unenhanced
07.11.2017 'Nathan Bridges Dune' on a Martian Mountain
07.11.2017 'Ireson Hill' on Mount Sharp, Mars
06.29.2017 Traction control testing
06.21.2017 A.I. laser targeting
06.01.2017 Diagram of Lake Stratification on Mars
03.21.2017 Break in Raised Tread on Curiosity Wheel
02.27.2017 Swirling Dust in Gale Crater, Mars, Sol 1613
02.27.2017 Dust Devil Passes Near Martian Sand Dune
02.27.2017 Sand Moving Under Curiosity, One Day to Next
12.13.2016 Now and Long Ago at Gale Crater, Mars
12.13.2016 Where's Boron? Mars Rover Detects It
10.03.2016 Curiosity Self-Portrait at 'Murray Buttes'
10.03.2016 Butte 'M9a' in 'Murray Buttes' on Mars
09.19.2016 Ribbon Cutting
09.09.2016 Farewell to Murray Buttes (Image 5)
09.09.2016 Farewell to Murray Buttes (Image 4)
09.09.2016 Farewell to Murray Buttes (Image 3)
09.09.2016 Farewell to Murray Buttes (Image 2)
09.09.2016 Farewell to Murray Buttes (Image 1)
08.26.2016 Out-of-this-World Records
03.30.2016 Erisa Hines
03.30.2016 Buzz Aldrin
02.12.2016 Women in Science
02.09.2016 Adam Steltzner, a JPL engineer
01.27.2016 Night Close-up of Martian Sand Grains
01.27.2016 Curiosity Self-Portrait at Martian Sand Dune
Scene of a Martian LandingThe four main pieces of hardware that arrived on Mars with NASA's Curiosity rover were spotted by NASA's Mars Reconnaissance Orbiter (MRO). The High-Resolution Imaging Science Experiment (HiRISE) camera captured this image about 24 hours after landing. The large, reduced-scale image points out the strewn hardware: the heat shield was the first piece to hit the ground, followed by the back shell attached to the parachute, then the rover itself touched down, and finally, after cables were cut, the sky crane flew away to the northwest and crashed. Relatively dark areas in all four spots are from disturbances of the bright dust on Mars, revealing the darker material below the surface dust.
Around the rover, this disturbance was from the sky crane thrusters, and forms a bilaterally symmetrical pattern. The darkened radial jets from the sky crane are downrange from the point of oblique impact, much like the oblique impacts of asteroids. In fact, they make an arrow pointing to Curiosity.
This image was acquired from a special 41-degree roll of MRO, larger than the normal 30-degree limit. It rolled towards the west and towards the sun, which increases visible scattering by atmospheric dust as well as the amount of atmosphere the orbiter has to look through, thereby reducing the contrast of surface features. Future images will show the hardware in greater detail. Our view is tilted about 45 degrees from the surface (more than the 41-degree roll due to planetary curvature), like a view out of an airplane window. Tilt the images 90 degrees clockwise to see the surface better from this perspective. The views are primarily of the shadowed side of the rover and other objects.
The Curiosity rover is approximately 4,900 feet (1,500 meters) away from the heat shield; about 2,020 feet (615 meters) away from the parachute and back shell; and approximately 2,100 feet (650 meters) away from the discoloration consistent with the impact of the sky crane.
The image scale is 39 centimeters (15.3 inches) per pixel.
Complete HiRISE image products are available at: http://uahirise.org/releases/msl-descent.php.
HiRISE is one of six instruments on NASA's Mars Reconnaissance Orbiter. The University of Arizona, Tucson, operates the orbiter's HiRISE camera, which was built by Ball Aerospace & Technologies Corp., Boulder, Colo. NASA's Jet Propulsion Laboratory, a division of the California Institute of Technology in Pasadena, manages the Mars Reconnaissance Orbiter Project for NASA's Science Mission Directorate, Washington. Lockheed Martin Space Systems, Denver, built the spacecraft.
Image Credit: NASA/JPL-Caltech/Univ. of Arizona